ZR-IA-DJYVP計算機電纜執行標準
GB/T 2951—2008 電纜絕緣和護套材料通用試驗方法
GB/T 2952 電纜外護層
GB/T 3048—2007 電線電纜電性能試驗方法
GB/T 3956 電纜的導體
GB 5441—85 通信電纜試驗方法
GB/T 6995 電線電纜識別標志
GB/T 9330.1-2008 塑料絕緣控制電纜 第1部分： 一般規定
GB/T 17650-1998 取自電纜或光纜的材料燃燒時釋出氣體的試驗方法
GB/T 19666-2005 阻燃和耐火電線電纜通則
JB/T 8137—1999 電線電纜交貨盤
JB/T 10696.7-2007 電線電纜機械和理化性能試驗方法 第7部分:抗撕試驗
ZR-IA-DJYVP計算機電纜生產流程：
1、導體
2、導體采用軟銅單線絞合而成（多股），其性能符合GB/T3956的規定。
3、導體表面光潔、無油污、無損傷絕緣的毛刺、銳邊、無凸起或斷裂的單線。
4、絕緣材料為氟塑料，采用鎳基合金高溫擠出機高速生產，擠包在導體上的絕緣性能符合Q/321023KLA11的規定。
5絕緣標稱厚度符合Q/321023KLA11的規定，絕緣厚度平均值不小于規定的標稱值，絕緣任一點Z薄點的測量厚度不小于標稱值的90%減去0.1mm。
6、火花
生產過程中絕緣層中間檢驗應按GB/T3048規定進行交流50HZ 6KV火花耐壓試驗。
7、對絞
對絞組采用顏色識別標志，每對線組由兩根不同顏色的單線和一條雙色扎帶組成。
8、對絞節距應不大于100mm。相鄰對絞組節距應不相同。
9、對絞屏蔽(二線組或三線組)
ZR-IA-DJYVP計算機電纜規格參數：
導體標稱 截面mm2 | 導體根數/單絲直徑mm | 20℃時導體直流電阻Ω/km | |||
A | B | R | A/B | R | |
1*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
1*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
1*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
1*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
1*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
2*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
2*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
2*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
2*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
2*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
3*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
3*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
3*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
3*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
3*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
4*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
4*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
4*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
4*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
4*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
5*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
5*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
5*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
5*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
5*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
6*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
6*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
6*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
6*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
6*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
7*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
7*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
7*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
7*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
7*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
8*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
8*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
8*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
8*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
8*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
10*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
10*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
10*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
10*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
10*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
12*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
12*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
12*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
12*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
12*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
14*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
14*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
14*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
14*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
14*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
15*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
15*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
15*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
15*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
15*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
16*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
16*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
16*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
16*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
16*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
18*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
18*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
18*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
18*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
18*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
20*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
20*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
20*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
20*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
20*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
22*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
22*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
22*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
22*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
22*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
24*2*0.5 | 1/0.80 | 7/0.30 | 16/0.20 | ≤36.0 | ≤39.0 |
24*2*0.75 | 1/0.97 | 7/0.37 | 24/0.20 | ≤24.5 | ≤26.0 |
24*2*1.0 | 1/1.13 | 7/0.43 | 32/0.20 | ≤18.1 | ≤19.5 |
24*2*1.5 | 1/1.38 | 7/0.52 | 30/0.25 | ≤12.1 | ≤13.3 |
24*2*2.5 | 1/1.78 | 7/0.68 | 49/0.25 | ≤7.41 | ≤7.98 |
